Güçlü bir Paslanmaz gövdeyi ve güçlü bir anahtarı kullanırken BarFlex, doğrudan Fren diski rotoruna Kompakt, çok güçlü bir Disk Kilididir.
Araç gövdesinin titreşimi tespit edildiğinde, bir aracın çalınmasını önlemek için gücünü, 120 dB'lik büyük hacimli PierceAlarm sesini çalarak gösteren bir üründür.
Su Yalıtım Özelliği ile Disk Kilit Gövdesi, özel yüzey işlemi uygulanarak lüks kaplama ile tamamlanır.
Dahili Lityum şarj edilebilir pil sistemi, yaklaşık 500 kez tekrarlanabilir.
Pil ayrıca USB ile şarj edilebileceği için ekonomiktir.
Bir şarj ile yaklaşık 4 ila 5 ay çalışacak. (Bu bağlıdır * Alarm operasyon sayısı)
Ayrıca, Alarm [AÇIK KAPALI] Bir işlevi var.
------ İşlem şekli ------
[ON / OFF anahtarlama yöntemi] * Alarm Gövdesi, Fren Diski'ni algılayan bir sensöre sahiptir.
● Disk Kilidi Gövdesini "P" Diskine yerleştirdiğinizde, sadece bir kısa bildirim sesi varsa, birkaç saniye sonra Güvenlik alarmının ONMODE olduğunu bildiren bir bip sesi duyulur.
Not: Güvenlik alarmının AÇIK konuma getirildiğini belirten bir bildirim sesi gelmeden önce Fren Diskinden çıkarırsanız güvenlik açılamaz. Kilitleme sırasında işlemi kontrol ettiğinizden emin olun.
● Disk Kilidi Gövdesini "Pippidi" ye yerleştirdiğinizde ve iki kısa bildirim sesi duyduğunuzda, Güvenlik alarmı KAPALI. (Kapatmanın zamanı olduğunu belirten bir bildirim sesi olmayacaktır.)
* Etkinleştirmeden sonra Güvenlik'i serbest bıraktıysanız, kilidi serbest bırakın ve Fren Diski'nden Disk Kilidini çıkarın.Alarm Gövdesi, Fren Diski'ni algılamayı durduracak ve alarm duracaktır.
[Şarj yöntemi]
1.Disc LockBody, discInsert parçası Cıvata. Bu nedenle ekli Altıgen Anahtarı ile donatılmış. Temizleyici.
* Altıgen Anahtar kullanırsanız, Fren Diski algılayan Sensör tepki verebilir ve duyulabilir.
2. Bolt'u çıkarırsanız, Cool devre dışı kalır.
3. AlarmUnit'i kaldırın, Su Geçirmez Kapağı çıkarın, Kabloyu USBConnector'a takın ve şarj edin.
* Lütfen Su Geçirmez Kapağın kaybolmadığından emin olun.
* AlarmUnit "Pi" kaldırılırken Kısa bir bip sesi duyulduğunda, lütfen tekrar itin ve AlarmUnit'i kaldırın. "Pippidi" Ve iki kısa bip, Güvenlik çalışmaz.
4. USB kablosu ile şarj edilirken, Mavi LED Lambası yanar.
5. LED sönünce şarj işlemi tamamlanır, lütfen AlarmUnit'i kurun.
* AlarmUnit'i kurarken, lütfen Su Geçirmez Kapak takmayı unutmamaya dikkat edin.
This is a compact, yet very strong disc lock with a strong stainless steel body and a strong key barrel that is directly attached to the brake disc rotor.
When it detects the vibration such as moving the vehicle body, it sounds the piercing alarm sound of 120dB, and it is the product which shows the power to prevent the theft of your vehicle.
In addition to waterproof specifications, the body of the disc lock is finished with a special surface treatment to give it a high-class look.
The built-in lithium rechargeable battery system can be used approximately 500 times.
The battery can be recharged by USB, so it is very economical.
It will run for about 4 to 5 months on a single charge.(*Varies depending on the number of times the alarm is activated)
In addition, the alarm has an [ON / OFF] function.
--- Operation ---
[How to switch ON / OFF] *The alarm is equipped with a sensor that detects the brake disc.
●When the main unit of the disc lock is inserted into the brake disc, a short "beep" will sound once, followed a few seconds later by a notification sound indicating that the security alarm is in the ON mode.
Note: The security alarm will not be switched on if it is removed from the brake disc before the audible notification that the security alarm is in the ON mode.When locking, always check the operation.
●When the disc lock unit is inserted into the brake disc, the security alarm will be turned off if there are two short "beep" sounds.(There will be no notification sound to indicate that the device is off.)
*To release the security system after it has been activated, release the lock and remove the disc lock from the brake disc.The alarm stops when the alarm body no longer detects the brake disc.
[charging method]
1. Remove the disc lock unit and disc insert bolt with the attached hexagonal wrench.
*If you use a hexagonal wrench, the sensor that detects the brake disc may react and make a sound.
2. Remove the bolt and the cover will come off.
3. Remove the alarm unit, remove the waterproof cover and attach the cable to the USB connector to charge the battery.
*Please do not lose the waterproof cover.
*If a short "beep" sound is heard once when the alarm unit is removed, push the alarm unit in again and remove it.If you hear a short "beep" sound twice when you remove the device, the security system will not be activated.
4. When you start charging with USB cable, blue LED lamp will light up.
5. Charging is complete when LED turns off.Install the alarm unit.
*When installing the alarm unit, be careful not to forget to attach the waterproof cover.