Sürüş sırasında vites konumunu gösteren gösterge.
Özel Kit.
Kurulum için gerekli tüm parçalar dahildir.
Belirli bisiklet modelleri için gerekli tüm parçaları içeren bir kit.
Özel Harness ile kurulumu kolay!
Her bisiklet türü için özel Kuşamlar, özel Kuşamlar kullanılır, bu nedenle lehimleme zahmeti olmadan kurulumu kolaydır.
* Bisiklet modeline özgü Harness, 12V (+) CS-550 hırsız alarmının kolay kurulumu için servis terminali.
Kompakt tasarım!
Gövde boyutları Gövde boyutları W25.5mm X H30.5mm X D15.5mm'dir. (çıkıntılı parçalar hariç) , bir metrenin etrafına kurulduğunda bile engel teşkil etmeyen kompakt tasarım.
LED ekran iyi bir görüş sağlar!
Dimmer Sensörü [otomatik karartma işlevi] tüm vücutta.
Dijital numaraların görünürlüğünü artırmak için LED parlaklığını gündüzleri daha parlak ve geceleri daha koyu olacak şekilde otomatik olarak ayarlar.
Bir Vites Yükseltme Göstergesi ile donatılmıştır!
Tüm vücuttaki dimmer sensörü, devir sayısının isteğe göre ayarlanmasına izin vererek, her şeyin sessizlik içinde çalışmasına ve aşırı devri önlemeye kadar her şeyin olmasına izin verir.
Dönüş, ayarlanan değerden daha yüksek olduğunda mavi LED yanar.
* İstediğiniz kadar yeniden kayıt yapabilirsiniz.
Özel Harness, Metrenin arkasındaki HarnessBlack12PCoupler'a bağlıdır.
Çalışma süresi: yaklaşık 60 dakika
Soru-Cevap
Q. Araç anahtarı AÇIK konuma getirildiğinde veya motor çalıştırıldığında ekran görünmüyor (LED Işık yanmıyor).
A. Artı veya Eksi kablosuyla zayıf temas olası bir nedendir. Lütfen Kablolamayı tekrar kontrol edin.
Q. Dişli konumunu ayarlarken, "5" mesajı belirir.
A. Ekran "5", "S" anlamına gelir ve hız göstergesi sinyali kullanılamayabilir.
Vücudun arkasındaki anahtara 3 kez bastıktan sonra "S" ve Shift Trump, GEAR'ı 1. vitese geçirdikten hemen sonra yanıp sönecektir.. "S" ve Shift Trump kaybolursa ve Nokta yanıp söner ve birkaç saniye sonra 1'e değişirse, kayıt sorunsuz yapılır.
S ekranı çalıştıktan sonra görünmeye devam ederse, lütfen aşağıdakilere bakın.
Elektrikli hızölçerler için, kabloların hız göstergesi kablosuna doğru şekilde bağlandığından emin olun.
Ayrıca, lütfen arızalı bir kablo bağlantısı olup olmadığını kontrol edin.
Mekanik durumunda (Kablo türü) Hızölçer, lütfen Opsiyonun PG-110'undan gelen kabloların SPI-110'un hız hattına doğru şekilde bağlanıp bağlanmadığını kontrol edin.
Ayrıca, lütfen arızalı bir kablo bağlantısı olup olmadığını kontrol edin.
Lütfen sensör ile mıknatıs arasındaki mesafenin 3-5 mm arasında olduğundan emin olun çünkü PG-110 Gövdesi yanlış takılırsa "S" görünebilir.
Ayrıca, her mıknatısın geçiş noktasının PG-110 sensörüne takılı mavi daire mühürden geçtiğinden emin olun.
Q. Dişli konumunu ayarlarken, "R" görüntülenir.
A. "R" işareti, motorun bir dönüş sinyali almadığını gösterir.
Kabloların Takometre sinyal hattına doğru şekilde bağlandığını kontrol edin.
Ayrıca, lütfen arızalı bir kablo bağlantısı olup olmadığını kontrol edin.
Q. Dişli konumunu ayarlarken "F" görüntülenir.
A1. Sürüş sırasında hem hız göstergesi sinyali hem de motor dönüş sinyali alınmıyor.
Lütfen her Kablolamanın iletişimini ve kurulum yöntemini onaylayın.
A2. Anahtar Nötr dışında bir GEAR'da açıldığında, "F" yanıp sönecektir.
Bu durumda, tekrar Nötr GEAR konumuna getirilip anahtarı KAPALI'dan AÇIK konuma getirerek "F" görüntülenmeyecektir.
A3. Tuş Nötr'de açıldığında bile "F" yanıp sönüyorsa, Shift göstergesinin Yeşil kablosu düzgün bağlanmamıştır.
Lütfen kablo bağlantı şemasını kontrol edin ve Nötr anahtara bağlayın.
12V Motorcycle Model Specific Shift Position Indicator
Meter to display the shift position while riding.
A kit for specific models.
All the parts you need for installation are ALL in ONE.
Shift data has been registered.
●All the necessary parts are included in this kit
●Special design!W400 gear position data already registered!
●Easy installation with special harness!
The special harness is designed for specific model, so you can install it easily without any soldering work.
*The vehicle-specific harness has a 12V (+) service terminal for easy installation of the CS-550 burglar alarm.
●Compact design!
The main unit dimensions are W25.5mm x H30.5mm x D15.5mm (excluding protruding parts), a compact design that does not interfere with installation around the meter.
●LED display for high visibility!
With a dimmer sensor on the entire surface [automatic dimming function]).
The brightness of the LED is automatically adjusted to be brighter in the daytime and darker at night to improve the visibility of the digital numerals.
●Equipped with a shift up indicator!
With a dimmer sensor on the entire surface, you can set the rotation speed arbitrarily to prevent over-revving.
The blue LED will light up when the rotation is higher than the set value.
*You can re-register as many times as you like.
The special harness is connected to the black harness 12P coupler on the back of the meter.
Approx. 60 minutes of work
Q&A
Q. When the vehicle key is turned on or the engine is started, the display does not show (LED light does not light up)
A. The positive wire or the negative wire may have poor contact.Check the wiring again.
Q. When setting the gear position, "5" is displayed
A. The display of "5" means "S", and there is a case that the speedometer signal is not taken.
After pushing the switch on the back of the unit three times, the shift lamp will blink "S" immediately after you put the unit into first gear, but if you start riding and the blinking "S" and the shift lamp disappear and the blinking dot appears and changes to the display of "1" a few seconds later, the unit has been registered without any problem.
If the S display continues to appear after you start running, please refer to the following.
For electric speedometers, check that the wiring is correctly connected to the speedometer wire.
Also, make sure that there is no poor contact between the wires.
In the case of a mechanical (cable) speedometer, check that the wiring from the optional PG-110 is correctly connected to the speed wire of the SPI-110.
Also, make sure that there is no poor contact between the wires.
Please make sure that the distance between the sensor and the magnet is within 3 to 5mm because "S" may appear if the PG-110 is installed incorrectly.
Also, make sure that the passage point of each magnet passes through the blue circle sticker attached to the sensor of PG-110.
Q.When setting the gear position, "R" is displayed.
A. The "R" display indicates that no engine speed signal is being received.
Check that the wiring is correctly connected to the tachometer signal wire.
Also, make sure that there is no poor contact between the wires.
Q.When setting the gear position, "F" is displayed.
A1. While driving, both the speedometer signal and the engine speed signal are not being obtained.
Check the contact of each wire and the installation method.
A2. When the key is turned ON in a gear other than neutral, "F" will blink.
In this case, put the vehicle in neutral gear and turn the key from OFF to ON, so that "F" will not be displayed.
A3. If "F" flashes even when the key is turned ON in neutral gear, the green wire of the shift indicator is not connected properly.
Check the wiring diagram and connect it to the neutral switch.