HIGHSIDER AKRON-RS plaka sahibi
HIGHSIDER AKRON-RS plaka tutucu, tasarımı sayesinde bisikletinizin hatlarına mükemmel uyum sağlar.
HIGHSIDER AKRON-RS'nin modele özel braketi, bisikletinizin orijinal montaj noktalarına monte edilmesini ve böylece daha fazla delme veya kesme işlemi olmadan değiştirilmesini sağlar..
Kabloların zarar görmesini önlemek için tüm keskin kenarlı burçlar kauçuk membran rondela ile korunur.
Plaka çelik sacdan yapılmıştır ve 2 mm kalınlığındadır.. Lazer ile hassas kesim yapılır.. Kenar kaplama işleminden sonra hava koşullarına dayanıklı siyah toz boya uygulanır.
Bu, optimum uyum ve dayanıklılık sağlar.
Kademesiz ayar sayesinde plakayı delmeden istediğiniz konuma getirebilirsiniz.. Plakayı bu konumda tutmak için ek bir kilitleme vidası vardır.
HIGHSIDER AKRON-RS'nin dönüş sinyali braketlerinin genişliği ayarlanabilir ve bu nedenle her türlü aksesuar dönüş sinyali için uygundur. Bu ayar seçeneği, dönüş sinyallerinizin konumunu en çeşitli plakalara uyarlamanıza olanak tanır.. Dönüş sinyallerini kablo demetinden ayırmadan monte etmeye izin vermek için, 10 mm'lik delikler yanlarda yarıklıdır.
Ayrıca bir kaydırıcı aracılığıyla reflektörün konumunu ayrı ayrı ayarlayabilirsiniz.. AB plakalarının farklı tasarımlarına uyarlama bu nedenle sorun değil.
Plakayı güvenli bir şekilde vidalamak ve titreşimi azaltmak için iki lastik rondela dahildir. Başka bir kauçuk tampon, alt tarafında plakayı destekler.
Detaylar:
- modele özel braket
- sonsuz ayarlanabilir dönüş sinyali tutucusu
- kablo ayırmadan kolay montaj için oluklu dönüş sinyali tutucusu
- sonsuz ayarlanabilir reflektör, E-onaylı
- Avrupa plakaları için uygun
- sonsuz ayarlanabilir eğim açısı
- optimum konum güvenliği için ek vida
- daha fazla çalışma adımı olmaksızın kolay sabitleme (e. gB. sondaj)
- plakanın yarıklı deliklerden kolay montajı
HIGHSIDER AKRON-RS'nin teslimat kapsamına şunlar dahildir:
- Montaj parçalarına sahip modelle ilgili braket
- HIGHSIDER AKRON-RS plaka tutma plakası
- Ayarlanabilir dönüş sinyali braketleri
- Ayarlanabilir braketli e-testli reflektör
- Montaj talimatları
Notlar:
- Orijinal plaka tutucunuza takılan yan reflektörler varsa, bunlar uygun bir konuma yeniden takılmalı veya yenileriyle değiştirilmelidir.
- Özel dönüş sinyali tutucusu 280-977, orijinal dönüş sinyalleri için isteğe bağlı olarak mevcuttur.
BAHŞİŞ:
Aracınız için modele özel bir plaka tutucusu bulamadıysanız, HIGHSIDER'ın birçok farklı tasarımı bulunan evrensel plaka tutucuları kesinlikle iyi bir alternatiftir.
HIGHSIDER AKRON-RS license plate holder
The HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your motorcycle thanks to its design.
The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your motorcycle and thus a replacement without further drilling or cutting.
To prevent damage to cables, all sharp-edged feedthroughs are protected by a rubber membrane grommet.
The license plate is made of sheet steel and 2mm thick. The precise cutting is done by laser. After edging, the weather-resistant black powder coating is applied.
This ensures the optimal fit and durability.
Through the full adjustable you can bring the plate without drilling in the desired position. To keep the plate in this position, there is an additional locking screw.
The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal. This adjustment option allows you to adapt the position for your turn signals to the most varied license plates. To allow mounting the turn signals without disconnecting them from the wiring harness, the 10mm holes are slotted to the side.
You can also adjust the position of the reflector individually via a slider. An adaptation to the different designs of the EU license plates is therefore no problem.
To screw the license plate securely and reduce vibration, two rubber washers are included. Another rubber buffer supports the license plate on its underside.
Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixation without further work steps (eg. Drilling)
- easy mounting of the license plate through slotted holes
Included in the scope of delivery of the AKRON-RS are:
- Model-related bracket with mounting parts
- AKRON-RS license plate mounting plate
- Adjustable turn signal brackets
- E-tested reflector with adjustable bracket
- Mounting instructions
Notes:
- For the original turn signals, the special turn signal bracket 280-970 is optionally available.
- If your original license plate holder has reflectors fitted to the side,these must be refitted in a suitable position or replaced with new ones.
Tips:
If you have not found a model-specific license plate holder for your motorcycle, the universal license plate holders from HIGHSIDER, which are available in many different designs, are certainly a good alternative.