Güç Sürücü Seti Tip 3

안녕하세요, 어제 제품을 수령하여서 확인해보 결과,도르래 그리스 (5.0g) X1 가 없이 배송되었습니다.배송상태는 양호하게 배송되었지만사진상 도르래 그리스가 빠진 상태로 배송되었습니다.확인 부탁드립니다~ 수고하세요 ----------------------------------------------------------Hello, me check results hayeoseo yesterday received the goods,The pulley Greece (5.0g) X1 is shipped without.Shipping status, although preferably ShippingThe photo shows Greek shipping pulleys were missing in the state.OK, thank you ~work hardPowered by Google Translator

i was running stock unit which was not performing well enough this setup with 6G rollers has fantastic acceleration and a massive improvement to top end speed (100kg rider in gear tops out at 80kph on flat roads with CDI upgrade)

Used for Honda DUNK.
Dunk Parts is still few, and at first I attached Mukawa's High Speed ??Pulley conforming to DUNK
.
Starting and accelerating was honestly honest just because I got a little bit of growth at the maximum speed without NORMAL and Large difference.
Because there is a change in the Exhaust System, slow speed is chilling, so WR is lightly set.
Later I installed High Speed ??Pulley for ZOOMER.
I am getting better and the maximum speed is 70 km / I got up to h place, but WR, Center spring etc, how to set 30 km / Rotation falls near h and does not accelerate to Smooth.
The face is on the verge and the angle is on the way from the middle of the Ramp Plate, where a valley is created for acceleration.
Make River's Ramp Plate was straight and accelerating was also straightforward, so I tried to use the Mampakawa's Ramp Plate, but the outer diameter is Small..
So, although it can be used for DUNK, the effect was written as slight, but since Ramp Plate is Straight and its outer diameter is larger than Mukawa Pulley, purchase it as a trial.
WR 5 g × 6 pieces and center spring 5% UP (Compared to ZOOMER Center spring) With Setting.
Since I was getting upset with acceleration and acceleration was not good, I put Slider in the center spring of LIVE DIO and tried it with WR 5 g × 6 pieces.
Beginning and accelerating also improved considerably 30 km / The valley of acceleration near h disappears and it accelerates to Smooth.
The maximum speed is 70 km / I think that it is near the h.
Therefore, OEM. 5 mm long 36. WR 4 g × 3 pieces in a 5 mm boss - Test run with 5 g × 3.
Even though I get better, the acceleration is slightly worse and the maximum speed is 58 km / It fell to h.
Just climb the slopes Guyugui.
Finally 4. 5 g × 3 - Setting completed with OEM boss to 5 g × 3 pieces.
It was pretty pleasant to start 0 and I felt that I was satisfied with acceleration and also the fastest speed.
I have tried 3 types of Pulley other than OEM so far, but this Pulley is the best.
To ignore the highest speed and climb up the slopes Guyguy 0. I put up a 5 mm Shim and I climb up considerably.
For DUNK riders it is Recommendation!

ชอบสินค้าแบรนkitacoมากเลยครับมีคุณภาพดีมากเลยครับรับลองครับใช้แล้วคุ้มค่าไม่ผิดหวังแน่นอนครับอย่ารอช้าคับรีบสั่งก่อนไม่มีให้สั่งนะคับของดีมีน้อยLike its rebranded kitaco lot of very good quality it was worth a try, then I am not disappointed Hurry, hurry, do not be the first to post a few of the well.(Google Translation)

I was thinking to introduce High Speed ??Pulley for exchanging the driving system, but since the face was worn out and it was able to step up, I used it as a whole set here.

It was my first time to replace the original drive system, but I can understand the difference clearly by exchanging.
Also, because this one has all but Weight Roller, I think that it is a good deal.